Ferrari 308 GTS 1980 BETA
Ferrari 308 GTS 1980 BETA
FerrarimanualclassicV8italy
The Ferrari 308 GTB berlinetta and targa topped 308 GTS are V8 mid-engined, two-seater sports cars manufactured by the Italian company Ferrari from 1975 until 1985. The 308 replaced the Dino 246 GT and GTS in 1975 and was updated as the 328 GTB/GTS in 1985. The similar 208 GTB and GTS were equipped with a smaller, initially naturally aspirated and later turbocharged, two-litre engine, and were sold mainly in Italy.
The 308 had a tube frame with separate body. The 308 GTB/GTS and GT4 were mechanically similar, and also shared much with the original Dino. Both 308s sit on the same tube platform, however the GT4—being a 2+2—has a longer wheelbase. The engine was a V8 of a 90 degree configuration, with two belt-driven overhead camshafts per cylinder bank. It was transversely mounted in unit with the transaxle transmission assembly, which was below and to the rear of the engine's sump. All models used a fully synchromesh[2] 5-speed "dog-leg" manual gearbox and a clutch-type limited slip differential. Suspension was all-independent, comprising double wishbones, coaxial coil springs and hydraulic dampers, and anti-roll bars on both axles; four wheel vented disc brakes were also fitted. Steering was unassisted rack and pinion.
The 308's body was designed by Pininfarina's Leonardo Fioravanti, who had been responsible for some of Ferrari's most celebrated shapes to date such as the Daytona, the Dino and the Berlinetta Boxer. The 308 used elements of these shapes to create something very much in contrast with the angular Bertone-designed GT4. GTS models featured a removable roof panel with grained satin black finish, which could be stowed in a vinyl cover behind the seats when not in use.
The Pininfarina-styled Ferrari 308 GTB was introduced at the Paris Motor Show in 1975[3] as a supplement to the Bertone-shaped 2+2 Dino 308 GT4 and a direct replacement for the two-seater Dino 246.
Its F106 AB V8 engine was equipped with four twin-choke Weber 40DCNF carburettors and single coil ignition. European versions produced 255 PS (188 kW; 252 bhp) at 6600 rpm (7700 rpm redline), but American versions were down to 240 PS (177 kW; 237 bhp) at 6,600 rpm due to emissions control devices. European specification cars used dry sump lubrication. Cars destined to the Australian, Japanese and US market were fitted with a conventional wet sump engine from the GT4.[3]
A notable aspect of the early 308 GTB was that, although still built by Carrozzeria Scaglietti, its bodywork was originally entirely made of glass-reinforced plastic (GRP), allowing a very light weight of 1,050 kg (2,315 lb). This lasted until June 1977, when the 308 was switched to steel bodies, resulting in an overall weight increase of approximately 150 kg (331 lb).
Five-spoke 14-inch alloy wheels were standard, while 16-inch wheels were made available later as an option together with sports exhaust system, high compression pistons, a high lift camshaft and a deeper front spoiler.
In 1980 Bosch K-Jetronic mechanical fuel injection was offered, leading to the 308 GTBi and GTSi; emissions decreased, at the price of a power drop to 214 PS (157 kW; 211 bhp) on European models and 205 PS (151 kW; 202 bhp) on federalized models. The fuel injection was coupled to a Marelli MED 803A Digiplex electronic ignition, incorporating a coil, distributor, and ignition module for each bank of cylinders.[6]
Outside, the car was identical to the 308 GTB/GTS, save for metric sized wheels of a slightly different design, fitted with Michelin TRX radial tyres—Michelin XWX on 16-inch wheels were optional. Inside, the clock and oil temperature gauge were moved to the centre console; there were also a new black steering wheel with three perforated spokes, and seats of a different pattern.
494 GTBis and 1743 GTSis were produced before the model was succeeded by the 308 Quattrovalvole in
Two years later, at the 1982 Paris Motor Show, Ferrari launched the 308 quattrovalvole, in GTB and GTS form.[9] The main change from the 308 GTBi/GTSi it succeeded were the four valves per cylinder—hence its name, quattrovalvole, literally "four valves" in Italian—which pushed output back up to 240 hp (177 kW) restoring some of the performance lost to the emission control equipment.
The new model could be recognized by the addition of a slim louvred panel in the front lid to aid radiator exhaust air exit, power operated mirrors carrying a small enamel Ferrari badge, a redesigned radiator grille with rectangular driving lights on each side, and rectangular (in place of round) side repeaters. The interior also received some minor updates, such as a satin black three spoke steering wheel with triangular centre; cloth seat centres became available as an option to the standard full leather. Available options included metallic paint, a deep front spoiler, air conditioning, wider, 16-inch Speedline wheels with Pirelli P7 tyres, and a satin black roof aerofoil (standard on Japanese market models).
Apart from the DOHC 32-valve cylinder heads, the V8 engine was essentially of the same design as that used in the 308 GTSi model. Total displacement was 2,927 cc (2.9 L; 178.6 cu in), with a bore x stroke of 81 mm × 71 mm (3.19 in × 2.80 in). Output on European specification cars was 240 hp (177 kW) at 7000 rpm and 260 N⋅m (192 lb⋅ft) at 5000 rpm of torque,[10] while for US specification variants were 230 hp (172 kW) SAE net at 6800 rpm and 255 N⋅m (188 lb⋅ft) at 5500 rpm of torque.[8] The gear and final drive ratios were altered to suit the revised characteristics of the four valves per cylinder engine. One other significant benefit of the QV's four valve heads was the replacement of the non-QV models sodium valves which have been known to fail at the joint between the head and the stem. Bosch K-Jetronic fuel injection and Magneti Marelli Digiplex electronic ignition were carried over from the GTBi/GTSi. All US market examples were fitted with catalytic converters.
The 288 GTO introduced in 1984 is considered as the first Ferrari supercar. The 288 borrowed much of the styling from the European 308 GTB QV of the previous year, 1983: it is also powered by a similar 2.8-litre V8 with a smaller bore and twin turbochargers, it retained the general bodywork lines with extended wheelarches, different side air vents, and bigger rear spoiler, longer (5 in (127 mm)) wheelbase, and the central tubular space frame chassis.
In 1985 Ferrari launched the 328, which replaced the Quattrovalvole. Between 1982 and 1985 the quattrovalvole was produced in a total of 3042 GTS and only 748 GTB examples.
The 308 had a tube frame with separate body. The 308 GTB/GTS and GT4 were mechanically similar, and also shared much with the original Dino. Both 308s sit on the same tube platform, however the GT4—being a 2+2—has a longer wheelbase. The engine was a V8 of a 90 degree configuration, with two belt-driven overhead camshafts per cylinder bank. It was transversely mounted in unit with the transaxle transmission assembly, which was below and to the rear of the engine's sump. All models used a fully synchromesh[2] 5-speed "dog-leg" manual gearbox and a clutch-type limited slip differential. Suspension was all-independent, comprising double wishbones, coaxial coil springs and hydraulic dampers, and anti-roll bars on both axles; four wheel vented disc brakes were also fitted. Steering was unassisted rack and pinion.
The 308's body was designed by Pininfarina's Leonardo Fioravanti, who had been responsible for some of Ferrari's most celebrated shapes to date such as the Daytona, the Dino and the Berlinetta Boxer. The 308 used elements of these shapes to create something very much in contrast with the angular Bertone-designed GT4. GTS models featured a removable roof panel with grained satin black finish, which could be stowed in a vinyl cover behind the seats when not in use.
The Pininfarina-styled Ferrari 308 GTB was introduced at the Paris Motor Show in 1975[3] as a supplement to the Bertone-shaped 2+2 Dino 308 GT4 and a direct replacement for the two-seater Dino 246.
Its F106 AB V8 engine was equipped with four twin-choke Weber 40DCNF carburettors and single coil ignition. European versions produced 255 PS (188 kW; 252 bhp) at 6600 rpm (7700 rpm redline), but American versions were down to 240 PS (177 kW; 237 bhp) at 6,600 rpm due to emissions control devices. European specification cars used dry sump lubrication. Cars destined to the Australian, Japanese and US market were fitted with a conventional wet sump engine from the GT4.[3]
A notable aspect of the early 308 GTB was that, although still built by Carrozzeria Scaglietti, its bodywork was originally entirely made of glass-reinforced plastic (GRP), allowing a very light weight of 1,050 kg (2,315 lb). This lasted until June 1977, when the 308 was switched to steel bodies, resulting in an overall weight increase of approximately 150 kg (331 lb).
Five-spoke 14-inch alloy wheels were standard, while 16-inch wheels were made available later as an option together with sports exhaust system, high compression pistons, a high lift camshaft and a deeper front spoiler.
In 1980 Bosch K-Jetronic mechanical fuel injection was offered, leading to the 308 GTBi and GTSi; emissions decreased, at the price of a power drop to 214 PS (157 kW; 211 bhp) on European models and 205 PS (151 kW; 202 bhp) on federalized models. The fuel injection was coupled to a Marelli MED 803A Digiplex electronic ignition, incorporating a coil, distributor, and ignition module for each bank of cylinders.[6]
Outside, the car was identical to the 308 GTB/GTS, save for metric sized wheels of a slightly different design, fitted with Michelin TRX radial tyres—Michelin XWX on 16-inch wheels were optional. Inside, the clock and oil temperature gauge were moved to the centre console; there were also a new black steering wheel with three perforated spokes, and seats of a different pattern.
494 GTBis and 1743 GTSis were produced before the model was succeeded by the 308 Quattrovalvole in
Two years later, at the 1982 Paris Motor Show, Ferrari launched the 308 quattrovalvole, in GTB and GTS form.[9] The main change from the 308 GTBi/GTSi it succeeded were the four valves per cylinder—hence its name, quattrovalvole, literally "four valves" in Italian—which pushed output back up to 240 hp (177 kW) restoring some of the performance lost to the emission control equipment.
The new model could be recognized by the addition of a slim louvred panel in the front lid to aid radiator exhaust air exit, power operated mirrors carrying a small enamel Ferrari badge, a redesigned radiator grille with rectangular driving lights on each side, and rectangular (in place of round) side repeaters. The interior also received some minor updates, such as a satin black three spoke steering wheel with triangular centre; cloth seat centres became available as an option to the standard full leather. Available options included metallic paint, a deep front spoiler, air conditioning, wider, 16-inch Speedline wheels with Pirelli P7 tyres, and a satin black roof aerofoil (standard on Japanese market models).
Apart from the DOHC 32-valve cylinder heads, the V8 engine was essentially of the same design as that used in the 308 GTSi model. Total displacement was 2,927 cc (2.9 L; 178.6 cu in), with a bore x stroke of 81 mm × 71 mm (3.19 in × 2.80 in). Output on European specification cars was 240 hp (177 kW) at 7000 rpm and 260 N⋅m (192 lb⋅ft) at 5000 rpm of torque,[10] while for US specification variants were 230 hp (172 kW) SAE net at 6800 rpm and 255 N⋅m (188 lb⋅ft) at 5500 rpm of torque.[8] The gear and final drive ratios were altered to suit the revised characteristics of the four valves per cylinder engine. One other significant benefit of the QV's four valve heads was the replacement of the non-QV models sodium valves which have been known to fail at the joint between the head and the stem. Bosch K-Jetronic fuel injection and Magneti Marelli Digiplex electronic ignition were carried over from the GTBi/GTSi. All US market examples were fitted with catalytic converters.
The 288 GTO introduced in 1984 is considered as the first Ferrari supercar. The 288 borrowed much of the styling from the European 308 GTB QV of the previous year, 1983: it is also powered by a similar 2.8-litre V8 with a smaller bore and twin turbochargers, it retained the general bodywork lines with extended wheelarches, different side air vents, and bigger rear spoiler, longer (5 in (127 mm)) wheelbase, and the central tubular space frame chassis.
In 1985 Ferrari launched the 328, which replaced the Quattrovalvole. Between 1982 and 1985 the quattrovalvole was produced in a total of 3042 GTS and only 748 GTB examples.
Best Lap Times
Track | Livery | Driver | Best Lap | |
---|---|---|---|---|
NO LAP TIMES HAVE BEEN SET IN THIS CAR! |
Report this mod!
If this mod has been made available but breaches terms and conditions please contact "@BLCKBOX - Hector" through DISCORD.
Specifications
-
Source Link Not Specified
-
-
Install with Content Manager
* Requires AC Content Manager Chrome or Firefox Extension